Robert Rowley Searches for the truth about the Perendev Magnet Motor. Just because I did not succeed does not mean that the other Perendev Videos are a fraud. Another configuration of magnets will be tested… If you look at my favorites on this same page you will see a drawing of the perendev cofiguration it shows that the magnets in the stator are magnetized through the diameter and not the poles. After doing hand tests I discovered that when the stator magnets are magnetized like the drawing shows the most powerful negative forces are reversed and become positive forces. The negative forces are shortened to almost nothing. Based on observation I would say this motor will work if built properly! I believe that the video of the Perendev Magnet Motor is authentic and that my attempt failed because I used the wrong configuration of magnets. In this video the magnets are all magnetized through the poles. When I did my research on the perendev I ignored a drawing showing magnets magnetized both ways being used. So apperantly I did some preliminary testing on what configuration might work and found that if the magnets in the stators are magnetized through the diameter that it causes something very different to happen as the magnets pass by eachother. It looks promising… Even though it only takes about 0 to buy the magnets for the next experiment I dont have it because I am a carpenter and business is slow because of the economy so I worry about losing my land at www …
10. April 2010 at 2:30 pm
look, you just got the idea wrong man, the magnets in this type of construction are NOT AXIALLY MAGNETIZED!! but DIAGONALLY. each one is “pulling” and then “pushing” from left to right , from side to side i mean..
10. April 2010 at 4:41 pm
Key is magnetic shielding, 50 lbs pulling mag use shielding can reduce drag to few lbs, Wang Sun Ho’s motor believed built this way.
Shielding is easy, just search for, Prendeve type motors will be everywhere 2 years from now. No interest group can stop this, Utbe has so many OU motors, i had lost the count, just simply do it, U’ll get there.
12. April 2010 at 8:35 pm
I have worked a lot with electric motors and I find that in the configuration of the magnets an error exists.although I find interesting the operation principle.with some adjustments it could work very well.
14. April 2010 at 6:33 pm
i think ur magnet placing mite b a tad off and erm also maybe sliding the rings ova the inner rings mite cause a spiraling effect of the magnetic field ova the inner rings causing them to spin n hope u didnt use aluminum but if anything it woulda bin the placing of the magnets
22. April 2010 at 12:26 am
the guy’s face already tells me that he likes to CON people…
24. April 2010 at 3:32 am
bismuth was used around each magnet for sheilding and feild direction on the pernedev
26. April 2010 at 9:15 am
Does the cat understand the law of conservation of energy? Nobody else around here seems to.
28. April 2010 at 2:14 am
Trial and error.
28. April 2010 at 6:06 am
back to the drawing board. 1st thing I noticed is your poles are off. If you go to the red and blue breakdown of the parendev, the stater has all north poles facing in. Where you messed up is the part where the rotor has split poles facing in north on the leading edge. try it again with some shielding and it will work
28. April 2010 at 6:17 am
@diveborg13 cool i would like to see
it thnks
3. May 2010 at 7:46 am
In the rotor the magnets are not installed correctly, there is a pattern you have to follow, starting from left to right you need to off-set each 1-2-3 by half its diameter, diagonally, then back from magnet 3 to magnet 1 keeping the off-set of half its diameter, therefore combining the repelling force even nullifying the push-back effect.
10. May 2010 at 5:34 pm
I invented a breakthrough energy source which violates the law of energy conservation. I have a PROOF that there are electrodynamic phenomena that violate the law of energy conservation. I am looking for $6M for a prototype and patents.
H. Tomasz Grzybowski
tel. +48-512-933-540
13. May 2010 at 2:29 am
It would appear the Pernedev bust is just another scam in a classic sting ending. The authorities bust the bad guy and all investments are not sought by investors, anymore. Classic sting movie theme.
Michael J Brady is most likely a ficticious character inveted to take the blame. Stories of his imprisonment cannot be found on any real news report sites. Only one free energy site has promoted this faery tale.
16. May 2010 at 3:29 am
did you place your magnets in shields. an aluminum cylinder with a cap on the back end should better direct your fields and reduce the negating field look under this for help(Part 1 One Way Magnetic Shielding The Holy Grail )
16. May 2010 at 1:19 pm
Hello
Wanted to give you my two cents on what I think may
be wrong with your design.
I think you might want to try using smaller magnets
that will fit your scale. I saw other videos of the same
type of motor and they are using about the same size
magnets as you are, but their motor is a much bigger
scale, and I think work better with that size magnet.
My want to try like I said to use a much smaller
magnet or to go to a bigger scale. Thats
my two cents. good luck! Charles S.
16. May 2010 at 4:23 pm
magnets should be turned around 19,45 degree, and not 60
the weels should have distance between ieach other, other wise, other weel magnets will interact.
and noone builds such huge project unless they tried it on smaller things, for example like a simple surface. the size of the wheel does not matter
16. May 2010 at 4:37 pm
check this video out – dT9s33X9D4I im not sure about 19,45 angle, thats the thing you have to find out your self. try it with 2 magnets first – one fixed, one on the tip of rotating stick – and try the angle, when you will figure out the angle then let us know
20. May 2010 at 1:26 am
use MU-Metal to shield the magnets
22. May 2010 at 6:19 pm
If you want the real deal,a real working magnet motor.The LT magnet motor is the best working magnet motor out there.
Just search for LT magnet motor and you can download the blueprints.
27. May 2010 at 6:58 pm
Problem.. No shielding.
4. June 2010 at 9:13 am
What people don’t seem to get about this “free energy” device made by Perendev, is there’s never been any actual, confirmed proof, that it works.
A shoddy video made by Perendev convieniently doesn’t pan around the device as it’s spinning up, and cuts out/restarts when the device is slowing down.
Perendev has claimed over many years that there will be a prototype and demo, but it’s never happened, because it’s fraud.
5. June 2010 at 2:47 am
nice job on the perendev, try the odd/ even number of magnets rotor/ stator thats the ticket all you have to do is change out the rotors to an odd number of magnets, they will be easyr to re-make then the stators. good luck
6. June 2010 at 7:13 am
Dude don’t waste ur time trying to harness smthin that is in violation of conservatn of energy, I can bet that even in a million yrs a mag energy device won’t be pssble.
7. June 2010 at 7:48 pm
so you made perpetual energy?
8. June 2010 at 11:58 pm
what did you use for the magnet housing?